Monday, November 17, 2014

Future of transport fourth mode :complete details of new vehicle design and explanation

Introduction:


INTRODUCTION

This paper deals with future of transportation when  energy will be scarce to move people and goods from one predetermined point to other. Author  considered ways to minimize loss of friction in moving of a vehicle Thus for same amount of energy greater distance can be traveled. Current mode of transportation and associated  loss due to friction is considered and new kind of engine with  additional caring  compartment is proposed .


Current practice’s:


Cars/Trucks
For both urban and highway driving, the mechanical energy that does
make its way through the driveline to turn the wheels is consumed by
three sinks: aerodynamic drag, rolling resistance, and braking. Braking
consumes momentum from the vehicle, which must be replenished by
acceleration. Because frequent stopping and starting entail repeated braking
and acceleration, braking is a major consumer of mechanical energy
during urban driving. In contrast, aerodynamic drag consumes relatively
more energy during highway driving since this resistive force escalates
with vehicle speed.

In comparison, the energy losses from rolling resistance (for a given
vehicle and set of tires) are mainly a function of miles traveled.














FIGURE 1 Example energy flows for a midsize passenger car:

(a) urban driving; (b) highway driving. [SOURCE: U.S. Department of Energy

 the energy lost per mile because of rolling resistance will be similar for a given vehicle and set of
tires over a widerange of urban or highway driving cycles. While the percentage contribution
of rolling resistance to total energy consumed per mile depends on
the contribution of other sinks, its absolute contribution does not.
In sum, for most conventional motor vehicles in common use, the
majority of the energy contained in motor fuel is dissipated as unrecoverable
heat from engine combustion and friction in the engine, driveline,
axles, and wheel bearings. Some of the energy output from the engine is
used during idling and to power vehicle accessories. Only about 12 to
20 percent of the energy originating in the fuel tank is ultimately transmitted
through the vehicle’s driveline as mechanical energy to turn the
wheels. Rolling resistance consumes about one-third of this mechanical
energy output. Rolling resistance, therefore, directly consumes a small
portion (4 to 7 percent) of the total energy expended by the vehicle.
However, reducing rolling resistance, and thus reducing mechanical
energy demand, by a given amount will translate into a larger reduction
in total fuel consumption because less fuel energy will need to be sent to
the engine in the first place.

Rolling resistance coefficient
Some typical rolling coefficients:
Rolling Resistance Coefficient

c
cl (mm)
0.001 - 0.002
0.5
railroad steel wheels on steel rails
0.001

bicycle tire on wooden track
0.002 - 0.005

low resistance tubeless tires
0.002

bicycle tire on concrete
0.004

bicycle tire on asphalt road
0.005

dirty tram rails
0.006 - 0.01

truck tire on asphalt
0.008

bicycle tire on rough paved road
0.01 - 0.015

ordinary car tires on concrete
0.03

car tires on tar or asphalt
0.04 - 0.08

car tire on solid sand
0.2 - 0.4

car tire on loose sand


Elecrical good Trains:-

 The "rolling resistance coefficient", is defined by the following equation:[5]

 F = C_{rr} N
where
F is the rolling resistance force (shown in figure 1),
C_{rr} is the dimensionless rolling resistance coefficient or coefficient of rolling friction (CRF), and
N is the normal force, the force perpendicular to the surface on which the wheel is rolling.
C_{rr} is the force needed to push (or tow) a wheeled vehicle forward (at constant speed on the level with no air resistance) per unit force of weight
As in electric engine trains / levitation trains  wheel/ axels- chassis  is made of very happy component , rolling resistance friction will be more  total  weight of engine/train.  Further  CRR is dependent on  friction between two surface and  creep between wheel circumfrance and stationary rail. Rails and railway wheels are much stiffer than pneumatic tyres and tarmac but the same distortion takes place at the region of contact. Typically, the area of contact is elliptical, of the order of 15 mm across.



http://bits.wikimedia.org/static-1.23wmf15/skins/common/images/magnify-clip.png
A torque M applied on the axle causes creepage: difference between forward velocity V and circumferential velocity \omega R, with resulting creep force F_w.
The distortion is small and localised but the forces which arise from it are large. In addition to the distortion due to the weight, both wheel and rail distort when braking and accelerating forces are applied and when the vehicle is subjected to side forces. These tangential forces cause distortion in the region where they first come into contact, followed by a region of slippage. The net result is that, during traction, the wheel does not advance as far as would be expected from rolling contact but, during braking, it advances further. This mix of elastic distortion and local slipping is known as "creep" (not to be confused with the creep of materials under constant load). The definition of creep[3] in this context is:






To overcome problem of
1, Inherent  Friction
2, Heavy  mass of train
Following is proposed

Solution :
future is where energy conversion to motion is maximum and this can be done by force generated on current carrying conductor in a magnetic field. This will give vehicle guiding force in direction of movement. Second is minimization of friction .  Both static and kinetic friction.  we plan to move vehicle having big wheels (mounted on bearings) over stationary array of rollers  to be used as track(mounted on bearings). two things will happen  first contact point where friction will be generator is reduced to contact area inside bearings (vehicle bearing and roller bearing of track).

Plan for big wheel for vehicle and small dia roller wheels is to avoid any jerk (vertical motion thus loss of energy) of vehicle . practically vehicle will glide over roller table. If rubber wheels of vehicle are big in comparison to roller table wheels then big wheel will be tangential to smaller roller table wheels. 
You can visualize  a big ball moving due to magnetic force on a  table consisting array of rolls mounted on bearings. 
two things will happen , ball will move forward and roller bearing will rotate as ball will glide over it. we propose to harness rotational energy of roller table wheels by attaching small generators). by this design we have removed static friction as ball is gliding on bearing mounted rolls  and we have limited friction loss to only frictional loss at bearings (both bearing of vehicle and roller table bearing) which is very small in comparison of normal mode of transportation where road/rail is stationary and  bearing mounted vehicle is moving over it.
Following points are to considered
1, This vehicle will move over a roller bed, 
2, vehicle will have multiple coaches
3, vehicle will propagate on forward on by magnetic fore generate by current carrying conductors , and external magnetic field applied. direction of magnetic field and current carrying conductor is such that vehicle will move forward.
4, vehicle  will have large wheels , so that on moving on small wheels at base it does give have any vertical impact on big wheels. Thus does less energy
5 ratio of  wheel dia  to roller dia should be max  limited by weight or any other design constraint.
6, small roller on surface will require less energy(rotational) when vehicle will move over it. 
7 , we can have mechanism to harness rotational energy of roller table rolls  after vehicle has travel-led  over it. To meet out energy required by accessories.
8, we may go for rubber rolls or(Vulkollan or polyurethane tread directly bonded to a steel) on both table and vehicle as whatever friction between them , actual energy loss due to friction will be  decided by contact area of bearings ( both on the roller table and vehicle wheels). There will some loss due to hysteresis due to regaining of shape of tyres.
9 What we are trying to do is , lowering the friction as vehicle will move over wheels and in turn , after initial thrust vehicle will move with very little frictional energy loss , and whatever energy loss in moving the base table rolls can be harnessed back by connecting them with generators.
10,Magnetic field  generator :  magnetic field  generator  are to be placed along the roller table tracks and sensors are to placed on vehicle and generators to energise  when vehicle is approaching generators



ENGINE DESIGN:- Following is considered while designing engine.
1 ,Minimisation of loss due resistance. . Copper current carrying conductor
2, High temp high compressive strength polymer as insulator. So as they do not fail on being pressed on the casing by current carrying conductor.
3, High temperature  alluminium alloy as casing . It can be Al – 8.5 %fe -Si – V   alloy or alloy with or
UNS
ANS
TEMPER
TS
YS
A0201
2010
T7
414(MIN)
345(MIN)
Or exhibiting better mechanical properties in tensile and compressive strength.
4, roller table rolls are to be made of  steel rolls mounted on bearings with polyurethane coating ( as case in roller coaster)
5 Non magnetic stainless steel block or aluminum alloy with high compressive strength at elevated temperature  in which current carrying conductors are to be placed to avoid hysteresis loss
6,  passage in block of stainless steel/alluminiuam for  forcing air for cooling engine.
7, external casing in which block is to be placed  and connected with rest of the vehicle made of  very  high strength Non magnetic stainless steel.
8 velocity  of vehicle will be controlled by strength of magnetic field generated by magnetic field generator.
9 direction of vehicle will be controlled by direction of current in current carrying conductors.


10,Friction will be lower in this case than the wheel of rail over rail track as surface are of contact will be area inside ball bearing and its casing  at both the (bearing of big ball and  roller table )
11, All rotational energy used for roller table rolls will be harnessed by couple small generators.
Details are in pdf files.
Note : this design will result in following
1, lower weight  of vehicle ,  thus lower  fore required to maintain constant speed.
2, lower friction hence lower crr thus  lower force required to maintain  constant speed.




1, Track roller table concept

2, Track roller table detials

3, Engine details














Conclusion : economy  of laying dawn tracks and  repair  may be an hindrance but  when  energy will be scarce then this will be future of transport.

FAQ: :- what will force vehicle in desired direction

Ans:  when  current carrying conductor is placed in placed in magnetic field than force is exerted on conductor by magnetic field which is perpendicular to both.

Magnetic Force

The magnetic field B is defined from the Lorentz Force Law, and specifically from the magnetic force on a moving charge:


The implications of this expression include:
1. The force is perpendicular to both the velocity v of the charge q and the magnetic field B.
2. The magnitude of the force is F = qvB sinθ where θ is the angle < 180 degrees between the velocity and the magnetic field. This implies that the magnetic force on a stationary charge or a charge moving parallel to the magnetic field is zero.
3. The direction of the force is given by the right hand rule. The force relationship above is in the form of a vector product.

When the magnetic force relationship is applied to a current-carrying wire, the right-hand rule may be used to determine the direction of force on the wire.

Question:- How direction of vehicle will be reserved. How vehicle will stop.
Answer:  Direction of vehicle will be reversed by  changing direction of current in conductor.  For figure above it can be seen that  force is perpendicular to both magnetic field and direction of current.  Change of direction will result force on conductors in opposite to motion of vehicle .
 Thus will work as breaks. By calibration we can move vehicle back also after stopping or start vehicle in reverse direction .

Question : how vehicle will accelerate
Answer:-   magnetic field clusters will be place at intervals. Each cluster will have number of   magnetic fields placed parallel to each other. First field of the cluster will give thrust to  the vehicle and second will give it further thrust to accelerate , next  field will give further push , till the time desired  velocity is achieved.  The for intermediate zone there will not be  any  magnetic field . what ever speed loss vehicle  will have  till it reaches next cluster of magnetic fields,  will be  replenished by  force on engine   by  new magnetic field cluster. 

Question :-  Why vehicle will not  be derailed
Answer: See figure  of big wheel moving on two track rolls. They are not below big wheel but are placed at angle . Or we may three roller table roll one at bottom and two as depicted in figure.



Question :  How  Engine will work
Answer:- Engine is designed with following main components:
1, Copper  current carrying conductor:   depicted as ( 1 )  in engine design above. Will be carrying current  and pull will be exerted on it by magnetic field in direction perpendicular to both direction of current and magnetic field.
2, High temp High strength polymer:  This polymer will have high compressive strength at high temperature.   As  heating of current carrying conductor will take place and  this conductor will be pressed against Engine block to provide thrust , High temperature  polymer with high compressive strength will be required.  It is depicted as (1) in engine design. Polymer will be non conductive to electrical current.
3,  High Compressive strength  Al alloy: This will  help in removal of heat  and sustaining  compressive force of current carrying conductor in to main block. This is depicted as (1) in engine design
4, Stainless steel plates for support:  As depicted in engine design  above ,  copper current carrying conductor , sleeved in  High temp High strength polymer, again sleeved in  High  compressive strength  AL alloy  will be mounted in  layered  non magnetic Austenetic  stainless steel  plates . This will give strength to engine  to transmit load to engine hosting  structure without any eddy current loss. Depicted as (2) in engine design
5, Vents :  Vents are designed for  follow of compressed air cooling  and arranged in staggered  way in design to provide all around cooling. Depicted as (3) in engine design.
6, Stainless steel block: Stainless steel blocks will host all component of engine and connect it/ mount with  big wheel. Depicted as (4) in engine.


why engine is  proposed to be made of stainless steel block can be  understood by following

Relative magnetic permeability

For some applications, it is necessary to use a stainless steel which has very low or negligible response to electromagnetic fields. A limit is then usually specified on the relative magnetic permeability of the steel (more often described simply as 'permeability'). The lowest relative magnetic permeability of a paramagnetic material is 1.0, i.e. the magnetic response of the material is the same as 'free space' or a complete vacuum.
The permeability of austenitic stainless steels is quite different from ferritic, martensitic and duplex stainless steels. Austenitic steels can be classed as 'paramagnetic' with relative permeabilities approaching 1.0 (generally in the range of 1.003 to 1.05 in the fully annealed condition). Use of  low permeabilities  austenitic steel is considered  for its strength to  trasfer  force to other part of engine , meanwhile magnetic field can thrust force on current carrying conductor  due to nearing to 1 relative magnetic permeability of the stainless steel.   


question :-